Fabrishare
Fabrishare

Guide · 2026

Heat-resistant 3D printing: which material copes with heat

Which 3D printing material withstands high temperatures?

It depends on how hot: PLA softens from about 55 °C and PETG from about 70 °C. ABS and ASA cope with about 90 °C, polycarbonate about 110 °C and carbon-fibre nylon up to about 150 °C. Above that come high-temperature resins, some of which go beyond 200 °C. Under load, any plastic softens sooner, so leave a margin of about 20 °C. Say in your project what temperature the part will reach and for how long, and makers will suggest the material.

How hot each material can get

Typical values without load: they vary with the brand, the part and how it's printed. With weight on it, allow about 20 °C less.

MaterialSoftens fromTechnologyWhat for
PLAAbout 55 °CFDMOnly parts that never get hot
Standard resinAbout 50–60 °CResinFine detail, away from any heat source
PETGAbout 70 °CFDMWarm water and mild heat
ABS and ASAAbout 90 °CFDM (enclosed printer)Car interiors, cases for devices that warm up
Polycarbonate (PC)About 110 °CFDM (enclosed printer)Boiling water, technical parts near engines
Nylon (PA), carbon-fibre filledAbout 100–150 °C depending on typeFDM, SLS or MJFMechanical parts that get hot and take strain
High-temperature resinFrom about 120 °C to over 200 °C depending on the resinResinMoulds, jigs and fixed parts next to a heat source

Beyond that are PEEK and PEI: they handle over 150 °C continuously, but need industrial printers that very few makers have.

What to ask for, by where the part goes

What matters is the real temperature and how long the part stays there, not the type of part:

Ask for

  • Inside a car, on the dashboard or parcel shelf: over 70 °C in summer. ABS or ASA.
  • In the engine bay, away from the exhaust and the block: polycarbonate or carbon-fibre nylon.
  • Hot water or the dishwasher: PETG is borderline; ABS, ASA or polycarbonate are better.
  • Cases for power supplies, motors or lamps that warm up: ASA or polycarbonate.
  • Moulds and masters for casting materials that heat up as they cure: high-temperature resin.

Avoid

  • PLA and standard resin near any heat source.
  • Any printed plastic next to an exhaust, a turbo, a flame or inside an oven.
  • Counting on the exact limit: a part carrying weight deforms well before it.
  • Parts touching hot food without a food-safe material: coping with heat doesn't make it safe.

How to order it so it doesn't fail

Give the temperature and the time

A few minutes at 90 °C isn't the same as 80 °C all day. The better you describe it, the better the material you'll be offered.

Say whether it carries load or is screwed down

Under load, plastic gives way sooner. A part that holds something or is clamped with screws needs more margin than a loose cover.

Ask about annealing

Some makers anneal the part in an oven after printing: it copes with more heat, but shrinks a little. If the dimensions are critical, mention it first.

Enclosed printer

ABS, ASA, polycarbonate and nylon need an enclosed printer so they don't crack while printing. Not every maker has one, which is why it's worth naming the material in your project.

What it costs

As a guide, a small FDM spare part is around €11 and a medium case or cover around €17 (excluding VAT and shipping). A technical material such as polycarbonate or carbon-fibre nylon adds a little to the material cost, but on a small part labour still weighs most in the price.

Parts for outdoor use: sun, water and heat
Car and motorbike parts
Masters for casting

How to order a part that copes with heat

  1. 1Post your project for free with the file, or photos and measurements if you don't have one.
  2. 2Say what temperature it will reach, for how long and whether it carries load. If you know the material, say so; if not, the maker will suggest one.
  3. 3Get offers with price and lead time within 24 hours, compare and choose.
Resin vs FDM: which for each part

Frequently asked questions

Which 3D printed material withstands the highest temperature?

Among the common ones, polycarbonate (about 110 °C) and carbon-fibre nylon (up to about 150 °C) in FDM, and high-temperature resins, some of which go beyond 200 °C. PEEK and PEI handle more, but need industrial printers.

At what temperature does PLA deform?

From about 55 °C. That's the temperature of a part in the summer sun or inside a car, so PLA only suits parts that never get hot.

Can PETG handle boiling water?

No: it softens from about 70 °C. For water at 100 °C, use polycarbonate, nylon or high-temperature resin.

Can a part be printed for a car engine?

Away from the exhaust, the turbo and the block, yes, in polycarbonate or carbon-fibre nylon. Next to the hottest areas, no printed plastic will last.

What is high-temperature resin?

A resin that copes with about 120 °C to over 200 °C depending on the type. It's rigid and precise but brittle: good for moulds, jigs and fixed parts, not for parts that take knocks.

Can a printed part go in the dishwasher?

PETG is borderline, because the hottest programmes reach about 65–70 °C. ABS, ASA or polycarbonate are better. If it will touch food, it also needs to be a food-safe material.

Does a heat-resistant material cost more?

A little more for the material, and not every maker has the enclosed printer that ABS, ASA, polycarbonate or nylon need. On a small part, labour still weighs more than material.